Jan 14, 2011 | Ruger 10/22 Barrels
Lightweight, aluminum replacement for factory barrel gives you the advantages of a short barrel, while the permanently attached muzzle shroud keeps the barrel length legal—no NFA transfer paperwork to worry about. Your flash suppressor with standard ½”-28 threads actually screws to the barrel inside the shroud, so it adds nothing to the barrel’s 16½” overall length. Machined from billet aluminum, with a .920″ O.D. and a chrome-moly steel bore liner to provide the rigidity and heat-transfer benefits of a bull barrel without the weight penalty. Oversized shank helps ensure a secure fit to almost any 10/22 receiver.
SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. Chrome-moly steel liner with 1-16″ twist rifling. 16½” (42cm ) O.A.L. including shroud, 12¼” (31.1cm) bore length, .920″ (2.3cm) O.D. Accepts muzzle accessories with ½”-28 tpi threads. Installation instructions included.
Dec 7, 2010 | Ruger 10/22 tools
You need to lay your Ruger 10/22 on some sort of mat to protect the rifle while service it, so why not use a mat that’s also an exploded view and parts list.
Manufacturers Description:
This isn’t your ordinary gun cleaning mat! Show your pride for your weapon while using this high quality neoprene rubber backed and cloth top gun cleaning mat to protect your gun bench, desk, kitchen table, or whatever surface you usually clean or maintain your gun on. You likely keep your gun in a soft padded case or maybe a gun cabinet with a felt lined rack or something similar to protect it so why would you scratch your gun while cleaning or repairing it by setting it on a hard surface that could easily scratch your firearm?
PROTECT YOUR GUN AND WORK AREA
The soft polyester top will ensure your gun doesn’t get scratched while the neoprene rubber backing on the mat will keep everything in place and prevent your work surface from sliding around. This mat will also keep harmful chemicals, oil and dirt from penetrating down to your desk, bench or the area where you normally clean and work on your firearms. After the mat begins to accumulate too much dirt, chemicals, or oil just throw it in the wash on a gentle cycle, allow to air dry and it will be virtually like new.
ENTERTAINING AND EDUCATIONAL
With the exploded view drawings and accompanying parts list, making repairs, disassembling your firearm, or basic cleaning can be done much faster and with greater enjoyment. Guns are extremely fascinating and the drawings and data that is printed on each mat will keep you entertained while educating you on how your firearm operates.
DIMENSION
This gun cleaning and parts mat measures 12 inches by 36 inches and is 1/8 of an inch thick.
PRODUCT DETAILS
This is made specifically for the Ruger 10/22 standard models but will also be very similar to all of the Ruger 10/22 varients as well as other rifles that take the .22 lr cartridge and are similar in design to the Ruger 10/22.
Oct 17, 2010 | Ruger 10/22 Stocks
UTG 10/22 Commando Tactical Quad Rail System
Based on the feedback I get at my combatrifle.net website there is no Ruger 10/22 accessory more popular than the UTG 10/22 Commando Tactical Quad Rail System.
Leapers UTG 10/22 Commando Tactical Quad Rail System
If anyone visiting this page owns a 10/22 with the Leapers UTG Commando Tactical Quad Rail System installed I would really enjoy some feedback and pictures.
Thanks!!
Oct 7, 2010 | Ruger 10/22 Charging Handle
RUGER 10/22 EXTENDED CHARGING HANDLE
Machined stainless steel charging handle with large deep, grooves is easy-to-grasp for lightning-quick charging and clearing. Case hardened, ground carbon steel guide pin provides exceptional strength for smooth cycling and improved feeding without bending or flexing. Includes fully assembled charging handle, guide pin, and extra power spring. Drop-in installation.
Oct 2, 2010 | Ruger 10/22 Magazine
Drop-in bolt stop stops forward travel of bolt when magazine is empty, ending the need to count shots; eliminates dry fires when the mag is empty. Replaces the factory bolt lock mechanism. Magazines are 10 round capacity with a rotary design and are constructed of high-impact plastic and steel. Important: Only use CST magazines with the bolt stop. Failure to do so may result in damage and accidental discharge. Works with most aftermarket products including mag latches, triggers, sears, hammers, etc. Kit comes with auto bolt stop and 10 round magazine.
If Blackdog Machine makes it you know it’s top notch.
Extra-tough, polymer magazines are self-lubricating and hold 25 rounds of .22LR ammo. Constant force spring provides uniform feeding and smooth loading. Two alternating, interlocking notches make it easy to click two or three mags together for fast reloads and increased shooting time. Available with separately molded, Polymer feed lips or Stainless Steel (SS) feed lips for optimum performance.
Durable, clear polymer 10/22 magazine holds fifty rounds of .22 long rifle ammunition. Steel feed lips provide years of reliable service. Rotating, coiled spring effectively feeds rounds on a rubber track system. Transparent body has numbers from 10 through 45 molded around the magazine: allows you to know exactly how many rounds you have left. Cover is removable for easy cleaning, and the unique tear drop shape fits comfortably in your hand for fast mag changes.
High capacity, 25-round magazine will wear for a lifetime because it is built from superior materials to never fail. Body halves are fully machined from a block of aluminum billet for superior strength, then secured with steel, socket head hex screws at three locations. Molded polymer follower and steel feed lips and center pin simply wont fail under the roughest use, even after many thousands of rounds. Magazine body can be completely disassembled for thorough cleaning. Hard-coat anodized finish prevents corrosion.
Easy-to-install kit gives your Ruger 10/22 the instantly recognizable appearance and handling of the classic, 1920-30’s submachine gun. For a fraction of the cost of an original, you can shoot a look-alike using plentiful .22 LR ammunition without putting wear on a historic heirloom. Kit includes all mounting hardware and tools, no gunsmithing required. Simply remove the 10/22’s barreled action from the factory stock, stake the two cross-pins in the trigger group, and install the kit components following the step-by-step instructions. The action fits securely into the kit’s precision-machined, billet aluminum chassis-no drilling or permanent alterations to the action are required, so you can return it to the original stock at any time. Like the original-production model, the kit’s three-piece stock is cut from high-quality, walnut with an attractive oil finish. Includes the rectangular, windage-adjustable rear peep sight of the early civilian subgun, and a clamp-on muzzle tip that slides around the factory front sight and replicates the profile of the original Cutts compensator. All the metal parts have a durable, semi-gloss blue-black powder coat finish. Kit available alone or with Pro-Mag 50-round drum magazine that lets you send plenty of rounds downrange between reloads and completes the iconic look of the Prohibition Era guns famous from movies and historic photographs. (Factory 10/22 magazines still work, too.) SPECS: Aluminum, powder coat finish, black, semi-gloss; walnut, matte finish. Kit includes receiver chassis, buttstock, pistol grip, forend grip, muzzle tip, front grip bracket, mounting hardware, and instructions. Available with or without Pro-Mag 50-round drum magazine. Spare magazines available separately.
So you bought some of these cool 10/22 magazines. Why not make the magazine changes a little quicker with Brownells Ruger 10/22 Extended Magazine Release lever.
This is pretty interesting. It connects three Ruger 10/22 Magazines together Click here for info. A possible solution to shooters facing magazine capacity issues.
Oct 2, 2010 | Ruger 10/22 Stocks
This is probably what sets the 10/22 apart from other .22 semi-auto rifles. You can go from mild to wild with bolt on ease. Traditional shooters my be content either upgrading to a synthetic or fancy laminated stock along the lines of the factory unit. However in my opinion the fun starts when you select a thumbhole or a competition oriented stock. Additionally there’s hardware to turn your 10/22 into a bullpup or something resembling an AR-15. Easy justification for owning more then one of these fine rifles. Below you’ll see some a random sampling from the inexpensive Hogue to the top of the line Bell & Carlson or FA Enterprises. If your interested in getting a 10/22 for a youth there is also a suitable stock for that purpose. Lastly before you head out and spend more on a stock then the guns purchase price be sure to see if one of Ruger’s 34 models doesn’t already suit your needs. Of course where’s the fun in that.
One thing to keep in mind when picking a new stock. Know the dimensions of your barrel or the barrel you intend to use so your sure to get one that fits properly. A standard barrel will look silly in a stock meant for a heavy barrel.
Sep 26, 2010 | Ruger 10/22 Barrels
I have an ER Shaw in one of my AR-15 and it’s a good shooter. I was unaware they produced Ruger 10/22 Barrels
Check out the technical specifications here at Brownells
E.R.Shaw Ruger 10/22 Barrels
Sep 23, 2010 | Ruger 10/22 Receivers
CNC machined aluminum chassis takes full advantage of proven technology and accepts off-the-shelf AR-15/M16 free float tubes, hand grips, receiver extensions, and buttstocks. Heavy duty upper and lower wraps-around around the original receiver to create a one-piece unit and provide the starting point for an outstanding tactical platform. Upper attaches firmly to the top of receiver for a rock-solid mount and improved accuracy. Includes a built-in Weaver-style base 6.5 inches long that allows a variety of options for mounting optics. Radiused edges give a streamlined appearance, reduce weight, and prevent snagging. Fits factory 10/22 barreled action and trigger group, including heavy barrels up to .990 inches in diameter. T6 aluminum hardcoat anodized for durability.
The receiver is CNC machined (no castings) from a solid billet of aircraft quality aluminum which is then hard anodized to provide for years of enjoyable shooting! The CNC machining process eliminates the burrs and rough surfaces that can be found in cast receivers. These burrs can create a drag on the bolt which can affect the performance of the rifle Each receiver is coated with a special lubricating finish that eliminates the need for frequent lubricating. The receiver is designed to be used with both Ruger factory bolts and trigger guards or for the ultimate shooting performance it is also compatible with the TG2000 trigger guard and the CNC Competition Bolt. The Superlite receiver is then fitted with a Weaver style base. Includes a hardened steel locking v-block, retaining screws and a hex head take-down action screw. This receiver is a must for any shooter looking to build up a semi-auto 22lr rifle.
